Winter Storage on a course

JAGJAG Posts: 169 Crazy Baller
So we have a new to us, Wally Sinker Course. Our club members are half divided in 1) removing the balls or 2) leaving them attached. Removing the balls seems like a lot of work in the spring, trying to raise the sand bag laden arms. The thought behind taking them off is so they stay cleaner for next year.

I'm of a single minority in removing the balls but attaching our worn, backup buoy's to ride out the cold.

I was wondering what everyone else does.

thanks,

Comments

  • bojansbojans Posts: 159 Baller
    Lots of variable here. Does your site freeze during the winter?
    Than_Bogan
  • DaveLemonsDaveLemons Posts: 265 Solid Baller
    If I leave mine on they freeze and pop when crushed by the ice
    davestaxidermystudio.com
  • JAGJAG Posts: 169 Crazy Baller
    Our lake freezes, to 12 or 13 inches in a very cold winter. The buoys are about five feet below the surface and I would think would be ok.

    thanks,
  • DaveLemonsDaveLemons Posts: 265 Solid Baller
    Wasn’t thinking about the sinking part
    One winter I left the balls on and the 2 ball arm ended up on the Sam side as the 1,3,5 side
    davestaxidermystudio.com
  • keithh2oskierkeithh2oskier Posts: 297 Solid Baller
    Our water doesn't freeze but our lake drops a few feet and all the buoys lay on their sides. Some sink (probably shot) and some float off. Either way in the spring the ones that remain are gross and usually need to be replaced. We have talked about putting milk jugs out there. Has anyone tried this? a few sources have them for cheap (under a dollar a piece.
    Than_Bogan
  • JAGJAG Posts: 169 Crazy Baller
    Milk jugs might be a good option. Didn't think of that. Thanks
  • thagerthager Posts: 3,815 Mega Baller
    My Accu-sink goes to the bottom for the winter with the balls on. Has worked fine for the last 15 years or so. In the spring brush off the balls. They will accumulate some scum.
    Stir vigorously then leave!
  • BraceMakerBraceMaker Posts: 1,849 Crazy Baller
    edited September 25
    The winter sun usually kills milk jugs. I'd consider clipping a retrieval bouy of something closed cell to the turn ball side gate bouy rope of each arm. So that it will sink but be easy to retrieve. Maybe even something with a big orange eye so you can snag it even when really cold.
  • EdbrazilEdbrazil Posts: 1,289 Historical Baller
    Dealt with a Wallycourse a good bit. In the Spring, the sandbags can get stuck into a
    muddy bottom, and need some help, such as by a SCUBA diver. Buoys also get nasty
    grungy.
  • BdeckerBdecker Posts: 181 Baller
    I’d leave them on and give a good scrub in the spring. The state made me remove and sink to the bottom over the winter. Basically made the system impossible given the work involved in spring and fall. If the system is going up and down reliably now, don’t touch a thing.
    JAG
  • APBAPB Posts: 32 Baller
    So easy to unclip the balls and use a few subs so you can find the lines.
  • lpskierlpskier Posts: 1,857 Mega Baller
    I pull my Accufloat. I know it's safe and I have the opportunity to inspect the cable and pipes for wear or damage. Takes four people a couple hours to put in and take out. Mine isn't a sinker, though, and that likely adds some steps and time. It might still be a good idea so you can inspect it.
    John Wilkins- Si non pro sanguine quem ludus ne. #iskiconnelly
  • davemacdavemac Posts: 444 Baller
    edited September 26
    if you leave the balls on (and submerged)...many recommend putting a plastic grocery bag over each of them....helps keep the winter scum off.
    JAGBdecker
  • thagerthager Posts: 3,815 Mega Baller
    @lpskier My accu-sink was a solid 12 hr install for two guys. Installed home made float course first followed by installing subfloats, bouys and airlines, securing each air line to cable and pvc arms with plastic safety ties, not to mention half bricks every 10 ft full length of course. Wally doesn't have bricks so a little time saving but, just sink it, It is easier. I put a plug over valve quick fitting,roll air line into circle, safety tie it, and cover with bricks in a few feet of water.
    Stir vigorously then leave!
  • JAGJAG Posts: 169 Crazy Baller
    thanks everyone for your ideas.
  • Chef23Chef23 Posts: 4,856 Mega Baller
    I like the idea of putting the old balls on for the winter. It would probably be faster than scrubbing them all in the spring.
    Mark Shaffer
  • thagerthager Posts: 3,815 Mega Baller
    @Chef23 Scrubbing takes maybe 20 minutes. Lot less time than when I put new ones on!
    Stir vigorously then leave!
Sign In or Register to comment.

Not sure how to deal with a long link?