2012 Mastercraft Prostar 197 Water pump bearing bad on 5.7 ILMOR engine.

oldmanskieroldmanskier Posts: 144 Baller
The main water pump (engine water pump) that bolts to the engine main bearing went bad.
I was not at the lake for a week due to work on call and when I came back the guys said the boat is making a loud noise around the pulleys.
They had been skiing it anyway for a couple of days with the boat making the noise.
I loosened the belt and could wiggle the main pulley on the water pump.
I could not believe the guys skied with the pulley having that much wobble. Surprised the belt did not come off or the pulley. The bearing in the Water pump was major worn out. I had them to quit using the boat until we can get a new water pump installed.
Question:
The guys want to go to an Auto Parts store and try to find a Water Pump that will fit our boat.
I want to order a Water pump that is for the our Mastercraft either from mastercraft dealer or a Boat parts place that has a Water pump for our boat.
Is a water pump from an auto parts store quality enough for a Ski Boat?
Thanks for any comments or suggestions.
oldmanskier.

Comments

  • DWDW Posts: 1,968 Mega Baller
    @oldmanskier : It all depends on the specific pump you get and your cooling system will determine the need. A marine pump will have a corrosion resistant impeller, either brass or plastic. A budget automotive pump may have a stamped steel one that can / will corrode in an open cooling system. You can get a marine one at various auto parts stores. If you have closed cooling and run antifreeze through the circulation pump, any pump will work just fine.
  • jpwhitjpwhit Posts: 60 Baller
    What @DW said, plus I believe the seals for a marine water pump are different. Automobile water pump seals are designed assuming there is anti-freeze, which has some lubricating properties. A boat water pump, for an open loop cooling systems, assumes the seals have to survive running in a straight water with no antifreeze.
  • AndreAndre Posts: 1,166 Crazy Baller
    edited August 2018
    Edit: Read the wrong year of boat,thought it was a 2017.

    I did replace my circulating pump with a marine one from NAPA.
    Was a perfect fit,came with both gaskets.
    At some point a 350 is a 350...
    You have open cooling or closed loop?
  • HortonHorton Posts: 27,149 Administrator
    dealer or known / trusted boat mechanic.

    Support BallOfSpray by supporting the companies that support BallOfSpray

    Barts ★ Connelly ★  DBSkis ★ Goode ★ Hobe Lake ★ HO Syndicate 

    MasterCraft ★ Masterline ★ MOB ★ Performance Ski and Surf ★ Reflex ★ Radar ★ Stokes

  • skihackerskihacker Posts: 302 Baller
    a reman auto parts store pump is likely $30, carry into a parts store, if a marine unit is available great, if not get whatever on hand and go ski. Swap over to a marine unit this winter when the water is hard and cold.
    eleeskiAndre
  • oldjeepoldjeep Posts: 3,377 Mega Baller
    edited August 2018
    Fwiw, gm recalled a crapload of narine water pumps in 2012 due to impellers cracking in half. Marine unit can be bought off amazon or any marine dealer. Auto pump will rot, they have sheet metal impeller.
    Chuck P
    Not a mechanic but I play one at home
  • Jody_SealJody_Seal Posts: 2,629 Mega Baller
    Amazon!
    Hobby Boats can be expensive when the hobbyist is limited on their own skill and expertise.


  • AndreAndre Posts: 1,166 Crazy Baller
    edited August 2018
    Jody ' s right.
    Ooops long link edited.
    Search amazon" marine water circulating pump" for small block chevy, 60$.

    Edit 2 :when i clicked on it, price went up to 85...???
  • oldmanskieroldmanskier Posts: 144 Baller
    Thanks for all the comments. They installed a New circulating pump but not for sure if it is a Marine pump or not. I will find out this weekend.
    oldmanskier
  • pcmcon729pcmcon729 Posts: 50 Baller
    My 2012 MC with 5.7 has been through 3 circ pumps, 2 raw water pumps, replaced non-stainless freeze plugs in manifold due to corrosion, and watch out for the 2 raw water intake hoses, for early 2012 production boats, the inner coil spring that keeps them from collapsing under suction were not stainless. Mine corroded and got sucking into the engine. Ilmor changed the quality of these poorly made components late model 2012. My old 2011 that I had sold to a buddy who keeps that boat on a different lake had all of the same issues with that boat.
Sign In or Register to comment.